Differences

This shows you the differences between two versions of the page.

--- qrp_labs_qcx_firmware [2019/10/12 10:30] – admin
+++ qrp_labs_qcx_firmware [2020/03/16 20:36] – admin
@@ Line 1: / Line 1: @@
 =====QRP Labs - QCX firmware upgrade with Raspberry Pi=====
-<color #ed1c24>WORK IN PROGRESS</color>
+-10-12 - Using a Raspberry Pi board as AVR programmer to update the QRP Labs QCX transceiver's firmware. The power draw from the QCX to the RPi seemed a bit too much, so I did not use the RPi 5v output.
--10-12 - Using a Raspberry Pi as AVR programmer.
+{{::img_2158.jpg?nolink&600|}}
-{{:img_1746.jpg?nolink&600|}}
+{{::img_2155.jpg?nolink&600|}}
 ====Requirements====
   * Raspberry Pi (I used a 3 model B+ board from 2017).
-  * Raspbian (based on Debian Buster)
+  * Raspbian (based on Debian Buster). Using ''/boot/ssh'' and ''/boot/wpa_supplicant.conf'' for headless install.
-  * Built and working QCX tranceiver. Website: [[http://qrp-labs.com/qcx.html]]
+  * A built and working QCX tranceiver. Website: [[http://qrp-labs.com/qcx.html]]
   * Jumper wires.
+  * QCX Firmware [[https://www.qrp-labs.com/qcx/qcxfirmware.html]]. Direct link (2019-10-12): [[http://qrp-labs.com/images/qcx/firmware/T1.01a.hex]]
+  * Connect a dummy load!
 ====Configure raspbian====
-  * Enable spi <code>dtparam=spi=on</code>
+  * Enable spi in ''/boot/config.txt'' and reboot: <code>dtparam=spi=on</code>
   * Install avrdude:<code>sudo apt install avrdude</code>
@@ Line 21: / Line 23: @@
 <code>
-============
 Raspberry Pi
-============
+=========================================
-BCM 9  (MISO)
+            (Right board edge)
-BCM 10 (MOSI)
+                   |
-BCM 11 (SCLK)
+oo|2
-BCM 25 (RESET)
+oo|4
-Ground
+oo|6
+oo|8
+oo|10
+oo|12
+oo|14
+oo|16
+oo|18
+BCM 10 MOSI - 19 oo|20
+BCM  9 MISO - 21 oo|22 BCM 25 RESET
+BCM 11 SCLK - 23 oo|24
+        GND - 25 oo|26
+<snip>
-============
 QCX
-============
+=========================================
 (left board edge)
@@ Line 46: / Line 60: @@
 </code>
-====programming====
+====Programming====
-  * Check connection:<code>sudo avrdude -p atmega328 -c linuxspi -P /dev/spidev0.0 -v -b19200</code>
+  * Check connection:<code>sudo avrdude -p atmega328p -c linuxspi -P /dev/spidev0.0 -v -b19200</code>
-  * Program latest firmware:<code>sudo avrdude -p atmega328 -c linuxspi -P /dev/spidev0.0 -v -b19200 -U flash:w:T1.00g.hex</code>
+  * Program latest firmware:<code>sudo avrdude -p atmega328p -c linuxspi -P /dev/spidev0.0 -v -b19200 -U flash:w:T1.01a.hex</code>